This crochet evergreen leaf lace table runner is a deep evergreen rectangular lace table runner with four columns of paired leaf clusters, arched openwork between the motifs, and a slim framed border. The construction is designed specifically for the named project rather than adapted from a generic template.
A 73-stitch foundation supports four 18-stitch leaf panels plus one edge stitch. An eight-row repeat builds paired leaf clusters over alternating chain arches and returns to a stable counted row; fifteen repeats form the runner before a slim border frames the lace.
Why You’ll Love This Project
The filet lace, leaf clusters, chain arches, framed border create a distinct table runner with clear checkpoints, practical structure, and strong handmade texture.
Materials
- Approximately 980 yards deep-evergreen sport-weight mercerized cotton yarn
- Eight locking stitch markers
- Rustproof blocking pins
- A row counter
- 3.25 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Gauge, Measurements, and Planning
Make a generous swatch in the main stitch. The target gauge is one 18-stitch leaf repeat measures 3 inches wide and one 8-row repeat measures 3.25 inches tall after blocking; change hook size if needed before beginning the full runner.
Make and wash a gauge swatch before beginning. Measure only after the swatch is completely dry. If the stitch width differs, change hook size rather than pulling the working yarn tighter. Keep a written count at the end of every section so the finished edges remain balanced and the assembly points line up.
Abbreviations and Special Stitches
- ch: chain
- dc: double crochet
- hdc: half double crochet
- sc: single crochet
- sl st: slip stitch
- st(s): stitch(es)
- BLO: back loop only
- yo: yarn over
Special stitch guidance: Leaf cluster: close three partial treble crochets together, chain 3, and close three more partial trebles in the same base. Bridge arch: chain 5 and single crochet in the neighboring leaf tip.
Before You Begin
- Maintain the stated 73-stitch construction count at every checkpoint.
- Beginning chains count only where explicitly stated.
- Block components before final assembly or border work.
- Use US crochet terminology throughout.
Instructions
Mark Four Evergreen Panels
Count carefully and compare the work with the finished measurements.
- Foundation Row: Ch 76. Dc in the fourth chain from the hook and across. Turn. (73 sts)
- Row 1: Ch 3, dc across. Turn. (73 sts)
- Mark the edge stitch and four 18-stitch panels so every leaf column remains aligned.
Open the First Leaf Pairs
Count carefully and compare the work with the finished measurements.
- Row 2: Edge dc, then repeat [ch 5, skip 5, leaf cluster in next stitch, ch 5, skip 5, boundary dc] four times. Turn.
- Rows 3–4: Expand each leaf pair with chain-3 sides and treble-cluster tips.
- Join neighboring leaf tips with chain-5 bridge arches without changing the 73 counted positions.
Complete Fifteen Lace Repeats
Count carefully and compare the work with the finished measurements.
- Rows 5–7: Mirror the leaf shaping while closing each pair into the next solid anchor row.
- Row 8: Dc in every established stitch or chain-space position. (73 sts)
- Repeat Rows 1–8 fourteen more times for fifteen repeats and approximately 48 inches.
Frame and Block the Runner
Count carefully and compare the work with the finished measurements.
- Work one round of sc evenly around with 3 sc in each corner.
- Work a second round of [ch 2, skip 1, sc in next stitch], keeping all four corners square, then finish with slip stitch.
- Wet-block every leaf pair and bridge arch to 15 by 50 inches.
Assembly and Shaping
Follow the project-specific assembly sequence for evergreen leaf openwork runner. Pin or mark every component before joining and keep the finished layout balanced.
Lay every component on a flat surface before joining. Match the marked centers first, then divide each remaining edge into equal sections. Work through both layers with consistent tension and pause after each section to check that the fabric lies flat. This measured approach prevents twisting and keeps decorative details facing the intended direction.
Finishing
- Weave every tail through matching stitches and reverse direction once.
- Inspect all joins, motif anchors, and border corners.
- Block to 15 inches wide by 50 inches long.
- Allow the runner to dry completely before styling.
For a polished result, weave each tail through several same-color stitches, reverse direction once, and trim only after the fabric has been gently stretched. Block to the listed dimensions without flattening textured stitches. Inspect joins, borders, straps, and decorative pieces before the project is used or gifted.
Helpful Tips
- Use locking markers at every construction checkpoint.
- Record row and motif counts as you work.
- Keep joins and color changes relaxed enough to lie flat.
- Photograph the complete layout before final assembly.
Good lighting and a contrasting stitch marker make counting much easier. If a section looks uneven, compare the current count with the previous checkpoint before continuing. Fixing one missed stitch early is faster than compensating later, and it preserves the measurements used by the assembly instructions.
Frequently Asked Questions
Can I make the leaves lighter?
Use a pale sage cotton while preserving the same stitch counts and blocking points.
How do I keep the columns straight?
Retain all eight markers and count 73 positions on every return row.
Can I lengthen the runner?
Add complete eight-row repeats; each blocked repeat adds about 3.25 inches.
Conclusion
The finished crochet evergreen leaf lace table runner showcases filet lace, leaf clusters, chain arches, framed border in a construction that matches the project from foundation through finishing.
Printable Crochet Pattern Card
Project: Crochet Evergreen Leaf Lace Table Runner
Skill level: Intermediate Hook: 3.25 mm Yarn: Sport
Finished size: Approximately 15 inches wide by 50 inches long
Card Materials
- Approximately 980 yards deep-evergreen sport-weight mercerized cotton yarn
- Eight locking stitch markers
- Rustproof blocking pins
- A row counter
- 3.25 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Card Instructions
- Mark Four Evergreen Panels: Foundation Row: Ch 76. Dc in the fourth chain from the hook and across. Turn. (73 sts) Row 1: Ch 3, dc across. Turn. (73 sts) Mark the edge stitch and four 18-stitch panels so every leaf column remains aligned.
- Open the First Leaf Pairs: Row 2: Edge dc, then repeat [ch 5, skip 5, leaf cluster in next stitch, ch 5, skip 5, boundary dc] four times. Turn. Rows 3–4: Expand each leaf pair with chain-3 sides and treble-cluster tips. Join neighboring leaf tips with chain-5 bridge arches without changing the 73 counted positions.
- Complete Fifteen Lace Repeats: Rows 5–7: Mirror the leaf shaping while closing each pair into the next solid anchor row. Row 8: Dc in every established stitch or chain-space position. (73 sts) Repeat Rows 1–8 fourteen more times for fifteen repeats and approximately 48 inches.
- Frame and Block the Runner: Work one round of sc evenly around with 3 sc in each corner. Work a second round of [ch 2, skip 1, sc in next stitch], keeping all four corners square, then finish with slip stitch. Wet-block every leaf pair and bridge arch to 15 by 50 inches.
Finish: Check every count, weave in all ends, block to measurement, and inspect each join.
