This crochet lattice kitchen towel holder is a small, useful project designed for focused beginner-friendly crochet sessions. Every section uses US terminology, realistic dimensions, and explicit checkpoints so the finished piece matches the title and intended function.
The towel holder construction uses a narrow lattice strap is worked flat with an integrated buttonhole and secured around a towel and appliance handle. Work the counted foundation first, check the gauge, and keep the stitch total recorded before moving to finishing.
Why You’ll Love This Project
The compact scale of this crochet lattice kitchen towel holder makes it easy to complete without a long commitment. The straightforward repeat gives you visible progress while the final edging and blocking create a polished, useful result.
Materials
- Approximately 60 yards cream worsted-weight cotton yarn
- Approximately 10 yards sage worsted-weight cotton yarn
- 4 mm crochet hook
- One 1-inch washable button
- Two stitch markers
- Yarn needle
- Scissors
- Tape measure
Gauge, Measurements, and Planning
Work the 12-position lattice repeat for 8 rows. It should measure about 2.5 inches wide and 2 inches tall without stretching. The completed strap should reach 8 inches before the buttonhole row.
Make and wash a gauge swatch before beginning. Measure only after the swatch is completely dry. If the stitch width differs, change hook size rather than pulling the working yarn tighter. Keep a written count at the end of every section so the finished edges remain balanced and the assembly points line up.
Abbreviations and Special Stitches
- ch: chain
- sc: single crochet
- sl st: slip stitch
- st(s): stitch(es)
- rnd: round
- row: row
Special stitch guidance: Lattice row: repeat single crochet, chain 1, skip 1 across. On the following row, work each single crochet into the chain-1 space to preserve the open grid.
Before You Begin
- Count at the end of every row or round before continuing.
- Beginning chains do not count as stitches unless a step says otherwise.
- Keep the fabric flat and adjust hook size if the gauge is off.
- Use the finished measurements as the blocking target.
Instructions
Start the Strap
Use cream and keep the foundation chain relaxed.
- Foundation Row: Ch 13. Sc in the second chain from the hook and across. Turn. (12 sts)
- Row 1: Ch 1, sc in each stitch across. Turn. (12 sts)
- Row 2: Ch 1, sc in first stitch, repeat [ch 1, skip 1, sc in next stitch] five times, sc in last stitch. Turn. (12 stitch positions)
Build the Lattice
Work single crochet into each chain space instead of the skipped stitch below.
- Rows 3–24: Ch 1, sc in first stitch, repeat [ch 1, sc in next chain-1 space] five times, sc in last stitch. Turn. (12 stitch positions)
- Measure after Row 24; the strap should be close to 8 inches long.
- For a shorter appliance handle, remove lattice rows in pairs while preserving the button placement.
Shape the Buttonhole End
Keep the opening centered and large enough for the chosen button.
- Row 25: Ch 1, sc in first 4 positions, ch 4, skip the center 4 positions, sc in final 4 positions. Turn.
- Row 26: Ch 1, sc across, working 4 sc into the buttonhole chain. (12 sts)
- Fasten off. Sew the button 1 inch from the opposite end using doubled yarn and test the closure around a folded towel.
Assembly and Shaping
Fold the strap over the appliance handle, place the towel beneath the lower end, and button through both layers. The lattice section should lie flat without twisting and the button should sit centered on the towel.
Lay every component on a flat surface before joining. Match the marked centers first, then divide each remaining edge into equal sections. Work through both layers with consistent tension and pause after each section to check that the fabric lies flat. This measured approach prevents twisting and keeps decorative details facing the intended direction.
Finishing
- Weave each tail through several matching stitches and reverse direction once.
- Block or reshape the project to the listed finished measurements.
- Inspect the border, corners, joins, and any closure before use.
- Trim the tails only after the fabric is completely dry and stable.
For a polished result, weave each tail through several same-color stitches, reverse direction once, and trim only after the fabric has been gently stretched. Block to the listed dimensions without flattening textured stitches. Inspect joins, borders, straps, and decorative pieces before the project is used or gifted.
Helpful Tips
- Use a contrasting marker to make the first stitch easy to find.
- Photograph or note the stitch count at each checkpoint.
- If the edge ripples, check for accidental increases; if it cups, loosen tension or increase hook size.
- Cotton yarn is ideal for small home and table projects because it is firm and washable.
Good lighting and a contrasting stitch marker make counting much easier. If a section looks uneven, compare the current count with the previous checkpoint before continuing. Fixing one missed stitch early is faster than compensating later, and it preserves the measurements used by the assembly instructions.
Frequently Asked Questions
Can I change the size?
Yes. Add or remove complete repeats while keeping increases and decreases evenly balanced, then update the finished measurement.
What yarn is best?
The pattern is written for 70 yards worsted-weight cotton yarn. A similar smooth yarn can work, but check gauge and expect the finished size to change.
How should I wash it?
Follow the yarn label, reshape while damp, and dry flat so the edges and corners remain even.
Conclusion
The completed lattice towel holder keeps a kitchen towel within reach without adding bulk. Its open cotton strap dries quickly, while the reinforced buttonhole and securely sewn button support everyday use.
Printable Crochet Pattern Card
Project: Crochet Lattice Kitchen Towel Holder
Skill level: Easy Hook: 4 mm Yarn: Worsted
Finished size: Approximately 2.5 by 8 inches
Card Materials
- Approximately 60 yards cream worsted-weight cotton yarn
- Approximately 10 yards sage worsted-weight cotton yarn
- 4 mm crochet hook
- One 1-inch washable button
- Two stitch markers
- Yarn needle
- Scissors
- Tape measure
Card Instructions
- Start the Strap: Establish a 12-stitch strap and begin the open lattice repeat.
- Build the Lattice: Repeat the 12-position lattice row through Row 24 or to an 8-inch length.
- Shape the Buttonhole End: Create a centered four-chain buttonhole, reinforce it, and sew the button to the opposite end.
Finish: Check every count, weave in all ends, block to measurement, and inspect each join.
