This crochet christmas holly berry table runner is an ivory filet-lace runner with three open diamond medallions, twelve dark-green holly leaves, eighteen cranberry bobble berries, and a scalloped green edge. The construction is designed specifically for the named project rather than adapted from a generic table-runner template.
A 61-stitch ivory filet panel is worked for 100 rows with three integrated diamond medallions, then decorated with twelve holly leaves and eighteen berry bobbles before adding a green scalloped edge.
Why You’ll Love This Project
The filet lace, holly leaf motifs, berry bobbles create a distinct table accent with clear checkpoints, practical drape, and strong handmade texture.
Materials
- 650 yards ivory worsted-weight cotton yarn
- 190 yards dark-green cotton yarn
- 90 yards cranberry-red cotton yarn
- Twelve locking stitch markers
- 4 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Gauge, Measurements, and Planning
Make a generous swatch in the main stitch. The target gauge is 16 double crochet stitches and 8 rows = 4 inches; change hook size if needed before beginning the full runner.
Make and wash a gauge swatch before beginning. Measure only after the swatch is completely dry. If the stitch width differs, change hook size rather than pulling the working yarn tighter. Keep a written count at the end of every section so the finished edges remain balanced and the assembly points line up.
Abbreviations and Special Stitches
- ch: chain
- dc: double crochet
- hdc: half double crochet
- sc: single crochet
- sl st: slip stitch
- st(s): stitch(es)
- BLO: back loop only
- yo: yarn over
Special stitch guidance: Filet mesh: double crochet, chain 1, skip 1. Holly leaf: mirror graduated single, half-double, and double crochet stitches along both sides of a center chain. Berry bobble: close five partial double crochets together.
Before You Begin
- Maintain the stated 61-stitch construction count at every checkpoint.
- Beginning chains count only where explicitly stated.
- Block components before final assembly or border work.
- Use US crochet terminology throughout.
Instructions
Crochet the Ivory Filet Foundation
Count carefully and compare the work with the finished measurements.
- Foundation Row: With ivory, ch 64. Dc in the fourth chain and across. Turn. (61 sts)
- Rows 1–8: Alternate solid dc rows with filet mesh rows, maintaining 61 stitches.
- Mark the three centered medallion zones.
Build Three Lace Diamonds
Count carefully and compare the work with the finished measurements.
- Rows 9–36: Open the first diamond by increasing one mesh cell at each side, then mirror the decreases.
- Rows 37–72: Work the centered diamond twice more with eight solid rows between motifs.
- Rows 73–100: Complete the third diamond and matching end margin. (61 sts)
Make Holly Leaves and Berries
Count carefully and compare the work with the finished measurements.
- Make twelve dark-green pointed holly leaves with a raised center vein.
- Work eighteen cranberry five-dc bobbles and secure their centers.
- Arrange four leaves and six berries around each lace diamond.
Finish the Scalloped Green Edge
Count carefully and compare the work with the finished measurements.
- Work one dark-green sc round with 3 sc in each corner.
- Repeat [skip 2 stitches, 5 dc in next stitch, skip 2 stitches, sc] around.
- Block to 16 by 50 inches and lift every berry bobble.
Assembly and Shaping
Follow the project-specific assembly sequence for holly berry lace runner. Pin or mark every component before joining and keep the layout centered inside the border.
Lay every component on a flat surface before joining. Match the marked centers first, then divide each remaining edge into equal sections. Work through both layers with consistent tension and pause after each section to check that the fabric lies flat. This measured approach prevents twisting and keeps decorative details facing the intended direction.
Finishing
- Weave every tail through matching stitches and reverse direction once.
- Inspect all joins, motif anchors, and border corners.
- Block to 16 inches wide by 50 inches long.
- Allow the runner to dry completely before styling.
For a polished result, weave each tail through several same-color stitches, reverse direction once, and trim only after the fabric has been gently stretched. Block to the listed dimensions without flattening textured stitches. Inspect joins, borders, straps, and decorative pieces before the project is used or gifted.
Helpful Tips
- Use locking markers at every construction checkpoint.
- Record row and motif counts as you work.
- Keep joins and color changes relaxed enough to lie flat.
- Photograph the complete layout before final assembly.
Good lighting and a contrasting stitch marker make counting much easier. If a section looks uneven, compare the current count with the previous checkpoint before continuing. Fixing one missed stitch early is faster than compensating later, and it preserves the measurements used by the assembly instructions.
Frequently Asked Questions
Can I omit the appliques?
Yes; the three filet diamonds still create a complete lace runner.
Can I use white instead of ivory?
Yes; bright white creates a crisp traditional Christmas palette.
How do I keep filet cells square?
Keep chains relaxed and block the completed panel before attaching motifs.
Conclusion
The finished crochet christmas holly berry table runner showcases filet lace, holly leaf motifs, berry bobbles in a construction that matches the project from foundation through border.
Printable Crochet Pattern Card
Project: Crochet Christmas Holly Berry Table Runner
Skill level: Intermediate Hook: 4 mm Yarn: Worsted
Finished size: Approximately 16 inches wide by 50 inches long
Card Materials
- 650 yards ivory worsted-weight cotton yarn
- 190 yards dark-green cotton yarn
- 90 yards cranberry-red cotton yarn
- Twelve locking stitch markers
- 4 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Card Instructions
- Crochet the Ivory Filet Foundation: Foundation Row: With ivory, ch 64. Dc in the fourth chain and across. Turn. (61 sts) Rows 1–8: Alternate solid dc rows with filet mesh rows, maintaining 61 stitches. Mark the three centered medallion zones.
- Build Three Lace Diamonds: Rows 9–36: Open the first diamond by increasing one mesh cell at each side, then mirror the decreases. Rows 37–72: Work the centered diamond twice more with eight solid rows between motifs. Rows 73–100: Complete the third diamond and matching end margin. (61 sts)
- Make Holly Leaves and Berries: Make twelve dark-green pointed holly leaves with a raised center vein. Work eighteen cranberry five-dc bobbles and secure their centers. Arrange four leaves and six berries around each lace diamond.
- Finish the Scalloped Green Edge: Work one dark-green sc round with 3 sc in each corner. Repeat [skip 2 stitches, 5 dc in next stitch, skip 2 stitches, sc] around. Block to 16 by 50 inches and lift every berry bobble.
Finish: Check every count, weave in all ends, block to measurement, and inspect each join.
