This crochet easter bunny table runner is a joined strip of four pastel corner-to-corner panels with alternating cream bunny silhouettes, dimensional white tails, tulip dividers, and a soft sage border. The construction is designed specifically for the named project rather than adapted from a generic table-runner template.
Four 12-by-12-block corner-to-corner panels are charted with cream bunny silhouettes, joined in one row, decorated with four yarn tails, and framed with sage tulip dividers and a rounded border.
Why You’ll Love This Project
The c2c mini panels, bunny silhouettes, pom-pom tails create a distinct table accent with clear checkpoints, practical drape, and strong handmade texture.
Materials
- 220 yards each blush, sky, lavender, and pale-yellow cotton yarn
- 260 yards cream cotton yarn
- 120 yards sage cotton yarn
- Four small white yarn pom-poms
- 4 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Gauge, Measurements, and Planning
Make a generous swatch in the main stitch. The target gauge is one 12-block corner-to-corner panel measures 12 inches square; change hook size if needed before beginning the full runner.
Make and wash a gauge swatch before beginning. Measure only after the swatch is completely dry. If the stitch width differs, change hook size rather than pulling the working yarn tighter. Keep a written count at the end of every section so the finished edges remain balanced and the assembly points line up.
Abbreviations and Special Stitches
- ch: chain
- dc: double crochet
- hdc: half double crochet
- sc: single crochet
- sl st: slip stitch
- st(s): stitch(es)
- BLO: back loop only
- yo: yarn over
Special stitch guidance: C2C block: chain 3 and work 3 double crochet in a chain-3 space. Decrease block: slip stitch across one block before beginning the next. Bunny tail: tightly wrap and trim a one-inch yarn pom-pom.
Before You Begin
- Maintain the stated 3-stitch construction count at every checkpoint.
- Beginning chains count only where explicitly stated.
- Block components before final assembly or border work.
- Use US crochet terminology throughout.
Instructions
Crochet the First Bunny Panel
Count carefully and compare the work with the finished measurements.
- Foundation Block: Ch 6. Dc in the fourth, fifth, and sixth chains. (3 sts)
- Rows 2–12: Increase one C2C block at both ends while following the cream bunny chart. (12 blocks)
- Rows 13–23: Decrease one block at both ends to finish the square.
Make Four Pastel Panels
Count carefully and compare the work with the finished measurements.
- Repeat the chart in blush, sky, lavender, and pale yellow.
- Reverse bunny direction on the second and fourth panels.
- Block every completed panel to 12 inches square.
Join the Bunny Parade
Count carefully and compare the work with the finished measurements.
- Arrange the four panels in one row with alternating bunny direction.
- Join matching block edges in cream with flat slip stitches.
- Attach one small white yarn pom-pom tail to each bunny silhouette.
Add Tulip Dividers and Sage Border
Count carefully and compare the work with the finished measurements.
- Surface-crochet one small tulip stem over each of the three panel seams.
- Work sage sc evenly around with 3 sc in every corner.
- Add one rounded shell round and block to 16 by 48 inches.
Assembly and Shaping
Follow the project-specific assembly sequence for bunny silhouette motif runner. Pin or mark every component before joining and keep the layout centered inside the border.
Lay every component on a flat surface before joining. Match the marked centers first, then divide each remaining edge into equal sections. Work through both layers with consistent tension and pause after each section to check that the fabric lies flat. This measured approach prevents twisting and keeps decorative details facing the intended direction.
Finishing
- Weave every tail through matching stitches and reverse direction once.
- Inspect all joins, motif anchors, and border corners.
- Block to 16 inches wide by 48 inches long.
- Allow the runner to dry completely before styling.
For a polished result, weave each tail through several same-color stitches, reverse direction once, and trim only after the fabric has been gently stretched. Block to the listed dimensions without flattening textured stitches. Inspect joins, borders, straps, and decorative pieces before the project is used or gifted.
Helpful Tips
- Use locking markers at every construction checkpoint.
- Record row and motif counts as you work.
- Keep joins and color changes relaxed enough to lie flat.
- Photograph the complete layout before final assembly.
Good lighting and a contrasting stitch marker make counting much easier. If a section looks uneven, compare the current count with the previous checkpoint before continuing. Fixing one missed stitch early is faster than compensating later, and it preserves the measurements used by the assembly instructions.
Frequently Asked Questions
Can I omit pom-pom tails?
Yes; embroider a flat white circle for a fully washable finish.
Can I use one background color?
Yes; alternating bunny direction still separates the four panels.
How do I keep C2C panels equal?
Use the same yarn, hook, block count, and blocking template for all four.
Conclusion
The finished crochet easter bunny table runner showcases c2c mini panels, bunny silhouettes, pom-pom tails in a construction that matches the project from foundation through border.
Printable Crochet Pattern Card
Project: Crochet Easter Bunny Table Runner
Skill level: Intermediate Hook: 4 mm Yarn: Worsted
Finished size: Approximately 16 inches wide by 48 inches long
Card Materials
- 220 yards each blush, sky, lavender, and pale-yellow cotton yarn
- 260 yards cream cotton yarn
- 120 yards sage cotton yarn
- Four small white yarn pom-poms
- 4 mm crochet hook
- Yarn needle
- Scissors
- Tape measure
- Blocking mats and rustproof pins
Card Instructions
- Crochet the First Bunny Panel: Foundation Block: Ch 6. Dc in the fourth, fifth, and sixth chains. (3 sts) Rows 2–12: Increase one C2C block at both ends while following the cream bunny chart. (12 blocks) Rows 13–23: Decrease one block at both ends to finish the square.
- Make Four Pastel Panels: Repeat the chart in blush, sky, lavender, and pale yellow. Reverse bunny direction on the second and fourth panels. Block every completed panel to 12 inches square.
- Join the Bunny Parade: Arrange the four panels in one row with alternating bunny direction. Join matching block edges in cream with flat slip stitches. Attach one small white yarn pom-pom tail to each bunny silhouette.
- Add Tulip Dividers and Sage Border: Surface-crochet one small tulip stem over each of the three panel seams. Work sage sc evenly around with 3 sc in every corner. Add one rounded shell round and block to 16 by 48 inches.
Finish: Check every count, weave in all ends, block to measurement, and inspect each join.
